Schmid Watson Spezifikationen Seite 98
- Seite / 134
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Watson Ethernet
Operating Manual
Watson-Ethernet-Manual.doc
Version 3.3-01
7-36
Revision: 2010-01-20
The Ethernet statistics for the Watson Ethernet tabletop modem are similar:
NTU_PM> ETHERNET
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Ethernet Statistics: ETH DSL
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
InDiscards : 0 0
InErrors : 0 0
InNUcastPkts : 0 0
InOctets : 0 0
InUcastPkts : 0 0
InPause : 0 0
OutErrors : 0 0
OutNUcastPkts : 0 0
OutOctets : 0 0
OutUcastPkts : 0 0
OutPause : 0 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
InDiscards
Number of discarded packets during reception
InErrors
Number of errored packets received
InNUcastPkts
Number on non-unicast packet received
InOctets
Number of octets received
InUcastPkts
Number on unicast packets received
InPause
Number of pause frames received
OutErrors
Number of packets sent with errors
OutNUcastPkts
Number on non-unicast packet sent
OutOctets
Number of octets sent
OutUcastPkts
Number on unicast packets sent
OutPause
Number of pause frames sent
RESETETH Port
This command resets the Ethernet statistics for a particular port. On the Watson
Ethernet tabletop modem it is not required to specify a Port number.
7.4.3 Bit error rate tests
Bit error rate testing functions are available on the tabletop modems only.
STARTBER m dir p
The STARTBER m dir p command starts the pseudo random binary sequence
(PRBS) generator and bit error rate (BER) meter for a duration of m minutes.
The test signal generator sends a PRBS of length 2
15
-1 according to ITU-T
O.151 (p = 0) or a PRBS of length 2
11
-1 according to ITU-T O.152 (p = 1).
If dir is 0 then the PRBS is sent towards the remote modem and an external
hardware loop must be established at the user interface of the remote modem
(loopback connector).
Selecting dir = 3 will start an internal DSL bit error rate test which is indepen-
dent of the user interface. A loopback with LOOP2 on the remote modem must be
- Declaration of Conformity 3
- Limited Product Warranty 9
- Table of Contents 11
- 1 Related Documents 17
- 2 Overview 19
- 3 Modem Features 23
- 3.1.2 Multipair operation 24
- 3.1.4 Power Backoff 26
- 3.1.7 Wetting Current 28
- 3.1.8 Master / Slave 29
- 3.1.9 DSL Clocking 29
- 3.2.1 Ethernet over DSL 29
- 3.2.2 Ethernet Bridging 30
- 3.2.4 VLANs 31
- 3.2.5 VLAN Examples 31
- 3.2.7 Stacked VLANs 35
- 3.3.1 Ethernet over DSL 41
- 3.3.2 VLAN features 41
- 3.3.4 Cisco HDLC 42
- 3.4 Firmware update 43
- 3.5 Management 43
- DISCONNECT 45
- 3.7 Test loops 48
- 3.8 Password protection 49
- 4 Powering 51
- 5 LEDs and Alarms 53
- 5.2 Tabletop LEDs 54
- 5.3 Alarm Conditions 55
- 5.4 Alarm Relays 55
- 5.5 Initialization Errors 56
- 6 The Monitor 57
- 6.2 Addressing of Plug-ins 58
- 6.3 Naming of ports 59
- 6.4 Telnet Access 59
- 6.5.1 Welcome Screen 60
- 6.5.2 Menus 60
- 6.5.4 Tab completion 61
- 6.5.5 Help 61
- 6.5.6 Command History 61
- 6.5.7 Continuous Displays 62
- 7.1 Introduction 63
- 7.2.1 General Commands 64
- DEFAULT Configuration 66
- 7.3.1 Diagnostic 89
- 7.3.2 Status (Plug-in) 90
- 7.3.3 Status (Tabletop) 92
- 7.3.4 Alarms 93
- 7.3.5 Test loops 95
- 7.3.6 Reset Commands 95
- 7.4.1 G.826 Statistics 96
- 7.4.2 Ethernet Statistics 97
- 7.5.1 Connection control 100
- 7.5.2 Inventory 100
- 7.5.3 Password 101
- 7.5.4 Firmware Update 103
- 8 SNMP 105
- ENTITIY-MIB 106
- 8.1.3 SNMP Configuration 107
- 8.1.4 The Entity MIB 107
- 8.1.6 The ifTable 109
- 8.2 MIB Reference 110
- 8.2.5 RMON (RFC 2819) 111
- 8.2.6 IF MIB (RFC 2863) 111
- 8.2.11 MAU MIB (RFC 3636) 112
- 8.2.15 HDSL MIB 114
- 8.2.16 Schmid MIB 115
- 8.2.17 Watson MIB 115
- 9 Front and Rear Panels 117
- 10 Connectors and Cables 119
- 10.2 DSL Interface 121
- 10.2.2 DSL Cable 122
- 10.3 Ethernet Interface 123
- 10.4 Monitor Interface 123
- 10.5 Power and Grounding 124
- 11.1 Interfaces 127
- 11.2 Power Consumption 128
- 11.3 Ethernet 128
- 11.5 Management Functions 129
- 11.6 MTBF 129
- 11.7 Environment 130
- 12 Terminology 131
- 13 Product Order Codes 133
- Revision: 2010-01-20 134
Verwandte Produkte und Handbücher für Vernetzung Schmid Watson
Vernetzung Schmid Watson Technical Information
(292 Seiten)
(292 Seiten)
Vernetzung Schmid Watson Spezifikationen
(103 Seiten)
(103 Seiten)
Vernetzung Schmid Watson Installationsanleitung
(129 Seiten)
(129 Seiten)
Vernetzung Schmid Watson Spezifikationen
(130 Seiten)
(130 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.530 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern